Aerial
GMP C2 Lasher
C2 Cable Lasher GMP 71422 Lashes single or bundled cables up to 1-7/8. (46mm) onto stand sizes 1/4in to 3/8in. (6-10mm) diameter. New style strand lock swings out of the way for unobstructed overlashing Dual wire magaziness for loading two coils of stainless steel lashing wire. Light weight 35lbs (16kgs) Only 10in O.D. x 18.5in long (25 x 47 cm). The C2's tapered housing eases passage through treed areas.
GMP J2 Lasher
J2 Cable Lasher GMP 86070 Will lash any single or multiple aerial cables up to 3in (75mm) diameter accross on any suspension strand to 1/4in (6mm) to 7/16in (11mm). A factory modifiation will allow the lasher to accomodate 1/2in (12.7mm) strand if neccessary. Each of two ressessed magaziness will hold a 1200ft coil of .045in (365m of 1.1mm wire) lashing wire (or 450mm wire) The lashing wire is fully recessed and covered by the gate.
GMP Apollo Lasher
Apollo Cable Lasher GMP 70400 Under 39 pounds (17.7kgs) without wire, 12 - 1/2in (318mm) diameter. Lashers and telcom cable/innerduct combination, up to 4in (10cm) diameter. Lashes to strand sizes 1/4in. To 3/8in (6- 10mm) diameter. Holds two coils of industry standard wire .045in x 1200ft (1.1mm x 365) or .038in. X 1600ft (1mm x 488m).
GMP G Lasher
Cable Lasher GMP 10500 Lashes any cable from 21/2in to 5in (64 - 127mm) diameter, on strand from 11/32in (9-19mm) diameters with one or two left lay spiral wrappings of .065 diameter stainless steel wire. Nominal spacing between wraps is 161/2in (42cm).
GMP 1/4" x 300 Duct Rodder
GMP 1/4 x 300 Duct Rodder GMP 89206. GMP 1/4" x 300 1/4in (12mm) x 300ft (91m). Weight 171lbs (8 kgs) standard unmarked continuous duct rodders are used to pull or push lines or cables through ducts, tubes or conduits. Gmp's duct rodders are light weight, durable and corrosion resistant. They are coated with a tough UV stabilized safety orange polypropylene and are not affected by water.
GMP 1/4" x 500 Duct Rodder
GMP 1/4 x 500 Duct Rodder GMP 89210. GMP 89210. 1/4in (6.7mm) x 500ft (152m). Weight: 21lbs standard unmarked continuous duct rodders are used to pull or push lines or cables through ducts, tubes or conduits. Gmp's duct rodders are light weight, durable and corrosion resistant. They are coated with a tough UV stabilized safety orange polypropylene and are not affected by water.
GMP 3/8" x 600 Duct Rodder
GMP 3/8 x 600 Duct Rodder GMP 89230. 3/8" (9mm) x 600 (183m) standard unmarked continuous duct rodders are used to pull or push lines or cables through ducts, tubes or conduits. Gmp's duct rodders are light weight, durable and corrosion resistant. They are coated with a tough UV stabilized safety orange polypropylene and are not affected by water.
GMP 1/2" x 1000 Duct Rodder
GMP 1/2 GMP 89268. 1/2in (12mm) x 1000ft (305m) Weight 177lbs standard unmarked continuous duct rodders are used to pull or push lines or cables through ducts, tubes or conduits. Gmp's duct rodders are light weight, durable and corrosion resistant. They are coated with a tough UV stabilized safety orange polypropylene and are not affected by water.
GMP D Cable Block
GMP D Cable Block GMP 72680. This block is used for supporting a single cable up to 2-3/4in (70mm) diameter on 1/4 - 3/8in diameter on 1/4 - 3/8in (6-10mm) bair strand prior to the lashing process. This has a 300 load pound copasity rating. Weight 3.8 pounds
GMP F Cable Block
GMP F Cable Block GMP 08093. This cable is perfect for temporily sopporting any cable up to 2 3/4in (70mm) diameter on 1/4 - 3/8 (6-10mm) diamiter suspension strand during new construction or while overlasing to existing lashed cable. Weight 31 pounds.
GMP E Cable Block
GMP E Cable Block GMP 74055. The model E cable block is normally used for pulling in self support or prelashed cable and mounted with either a A,B,C,D,E cable block frame at a pole.
GMP Aerial Cable Guide
Aerial Cable Guide GMP 70055. The dual lashing aerial cable guide is used to guide and straingten cable as they are pulled into a lashing position from a stationary or mounting cable reel. Weight 11 poungs.
GMP 5" Cable Feeding Sheave
5 Cable Feeding Sheave GMP 70567. Cable feeding seaves slide into the end of conduit in a manhole wall allowing the cable being fed into the conduit to roll smootly over the sheave from all angles. Weight 27 pounds.
GMP 4" Cable Feeding Sheave
4 Cable Feeding Sheave GMP 70566. Cable feeding seaves slide into the end of conduit in a manhole wall allowing the cable being fed into the conduit to roll smootly over the sheave from all angles. Weight 23 pounds.
GMP 3" Cable Feeding Sheave
3 Cable Feeding Sheave GMP 70564. Cable feeding seaves slide into the end of conduit in a manhole wall allowing the cable being fed into the conduit to roll smootly over the sheave from all angles. Weight 17 pounds.

Order

Contact Us

California Office
1-800-256-5186
Georgia Office
1-888-800-1712




Lasher Repairs

A-Aerial specializes in cable lasher repairs and servicing. Two day emergency service is available. We also accept you’re dropped or damaged lasher as a trade-in toward a new unit. When sending lashers to us for repair, please include contact information and description of requested repair.

C lasher rebuild cost usually range from $1600.00 to $2400.00.

J2 lasher rebuild cost usually range from $1,800 to $2,600.

Refurbished Lashers

We sell used and refurbished cable lashers. All used and refurbished lashers have a 90 day warranty.

Used C lashers from $2,195

Refurbished C lashers from $2,595

Refurbished J2 Lashers from 3,450.00

Refurbished J2B (Modified with no strand lock.) Lashers from 3,250.00